22.05.2020 10:11, ОпятьДЗ

БРАТЬЯ И СЁСТРЫ
ответить на во Вот текст: Drawing consists of pulling metal through a die. One type is wire drawing. The diameter reduction that can be achieved in one die is limited, but several dies in series can be used to get the desired reduction. Sheet metal forming Sheet metal forming is widely used when parts of certain shape and size are needed. It includes forging, bending and shearing. One characteristic of sheet metal forming is that the thickness of the sheet changes little in processing. The metal is stretched just beyond its yield point (2 to 4 percent strain) in order to retain the new shape. Bending can be done by pressing between two dies. Shearing is a cutting operation similar to that used for cloth. Each of these processes may be used alone, but often all three are used on one part. For example, to make the roof of an automobile from a flat sheet, the edges are gripped and the piece pulled in tension over a lower die. Next an upper die is pressed over the top, finishing the forming operation, and finally the edges are sheared off to give the final dimensions. Forging Forging is the shaping of a piece of metal by pushing with open or closed dies. It is usually done hot in order to reduce the required force and increase the metal's plasticity. Open-die forging is usually done by hammering a part between two flat faces. It is used to make parts that are too big to be formed in a closed die or in cases where only a few parts are to be made. The earliest forging machines lifted a large hammer that was then dropped on the workpiece, but now air or steam hammers are used, since they allow greater control over the force and the rate of forming. The part is shaped by moving or turning it between blows. Closed-die forging is the shaping of hot metal within the walls of two dies that come together to enclose the workpiece on all sides. The process starts with a rod or bar cut to the length needed to fill the die. Since large, complex shapes and large strains are involved, several dies may be used to go from the initial bar to the final shape. With closed dies, parts can be made to close tolerances so that little finish machining is required. Two closed-die forging operations are given special names. They are upsetting and coining. Coining takes its name from the final stage of forming metal coins, where the desired imprint is formed on a metal disk that is pressed in a closed die. Coining involves small strains and is done cold. Upsetting involves a flow of the metal back upon itself. An example of this process is the pushing of a short length of a rod through a hole, clamping the rod, and then hitting the exposed length with a die to form the head of a nail or bolt.

Всего ответов: 2

Похожие вопросы:

Иконка предмета
Английский язык, 03.03.2019 17:24
Think pf more questions about the picture. then work in pairs. close your books and and test your partner's memory. ask your own questions and those from exercise 4
Ответов: 3
Иконка предмета
Английский язык, 03.03.2019 17:29
60 ! you recently bought a network online which does not recognise your modem. write a letter to the company according to the plan below: plan introduction para 1: greeting; the purpose of your writing. main body para 2: state when/where/how you bought it. para 3: explain what the problem is;
tell the company you are returning the gadget. conclusion para 4: ask them to repair it or send you a new one; closing remarks; your signature. write a letter of at least 100 words. do not write any dates and addresses.
Ответов: 2
Иконка предмета
Английский язык, 03.03.2019 19:30
Read this interview with a famous writer. write question words and phrases in the gaps.​
Ответов: 3
Иконка предмета
Английский язык, 03.03.2019 23:43
Write about your favourite russian film, explain why you like it. 12 предложений, пишите сами ! 15
Ответов: 1
Иконка предмета
Английский язык, 04.03.2019 10:23
Сделать на 1 картинку 1 сочинение (не менее 15 предложений) напишите хоть на
Ответов: 1
Иконка предмета
Английский язык, 07.03.2019 06:49
Writing plan. про любое и с переводом .​
Ответов: 2
Иконка предмета
Английский язык, 07.03.2019 14:37
Что это значит и как это делать? ( 22)
Ответов: 1
Иконка предмета
Английский язык, 11.03.2019 08:04
Нужно по этому тексту ответить на вопросы. через 30 минут контрольная всего 2 вопроса. у меня нет времени ​
Ответов: 1
Иконка предмета
Английский язык, 11.03.2019 15:19
Ex. 9. put special questions. begin with the question-words given in brackets. 1. the length of the bus route has been increased by 3 km. (how many) 2. the pipe is leaking at the joint. (where) 3. now all the european railways have a standard gauge. (what gauge) 4. the rails are called t-rails because of their shape. (why) 5. the load weighs a hundred kilograms. (how many) 6. for some period of time, one underground railway line in london was working without drivers. (where) 7. the two-speed escalators will be installed at new metro stations. (where) 8. in the samara metro, trains run at 8 minutes headways. (how often) 9. before the invention of steel, railway cars were made of wood. (what) 10. the builders will have to explode the rock to construct the railway in this district. (why) 11. double-deck buses were operating in moscow within several months. (how long) 12. passenger services on britain's railway network have increased by more than 30% during the past seven years. (how many) 13. the underground railways as a form of city transport appeared in the second half of the 19th century. (when) 14. train fares will go up by seven percent next week. (how many) 15. the embankment gradually sinks (оседать) under the weight of passing trains. (why)
Ответов: 2
Иконка предмета
Английский язык, 11.03.2019 17:33
Вподписях к этим картинкам есть ошибки . исправь их. the reeds are on the farm. the greens are by the lake. thevdobbins are in their street. the whites are in the park. the finns are in the car. the hoggs are on the plane.
Ответов: 1
Иконка предмета
Английский язык, 11.03.2019 19:13
2. use the prompts and a verb from the box to write past simple questions. read walk pay give eat buy win go study play 1. you/swimming yesterday? 2. she pizza last night? 3. they/tennis? 4. your teacher/you a test? 5. you/for the exam? 6. we/the bill? 7. your sister/you a present? 8. you/that book? 9. they/the game? 10. he/to the library?
Ответов: 3
Иконка предмета
Английский язык, 11.03.2019 19:23
Надо написать 15 предложений о 3 достопримечательностях ташкента​ на
Ответов: 3

Вопросы по другим предметам:

Популярные вопросы
Вопросов на сайте: 19213143